VTech DS3111-3 Manuel d'utilisateur télécharger pdf

Quick start guide for model DS3111-2

NOTES:

1. Use only the power adapters and batteries supplied with your VTech

telephone.

2. For complete feature instructions, please refer to your user’s manual.

96-006499-030-100

issue 2

IMPORTANT!

If your product is not working properly:

Refer to the Troubleshooting section of the user’s manual.

Visit our website at www.vtechphones.com.

In Canada, go to www.vtechcanada.com.

Call our customer service at 1 (800) 595-9511.

In Canada, call 1 (800) 267-7377.

•

Telephone base installation

We recommend that you install the telephone base away from any electronic

equipment and appliances such as personal computers, computer routers,

television sets, microwave ovens or refrigerators. Avoid excessive heat,

cold, dust or moisture. When a location is selected, install the telephone

base and the charger as shown below. Make sure that the electrical outlet

is not controlled by a wall switch.

MANUFACTURED IN CHINA

COMPLIES WITH 47 CFR PART 68

REGISTRATION NO.: US:EW7W401B80-565600

RINGER EQUIVALENCE: 0.1B

USOC JACK: RJ11C/RJ11W

HAC FCC ID: EW780-5656-00

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO

THE FOLLOWING TWO CONDITIONS: 1) THIS DEVICE MAY NOT CAUSE HARMFUL

INTERFERENCE; AND 2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,

INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. PRIVACY OF

COMMUNICATIONS MAY NOT BE ENSURED WHEN USING THIS PHONE.

DC 6V 300mA

CLASS 2 POWER SOURCE ONLY

TELEPHONE

EQUIPMENT

Telephone

wall jack

Electrical outlet

not controlled

by a wall switch

Power adapter

Charger adapter

Telephone

line cord

Handset battery installation

Install the handset battery by following these steps:

1. Align the two holes of the battery plug with the socket pins in the handset

battery compartment, matching the red and black wires to the color-

coded label.

2. Place the battery in the compartment with the wires in the lower right

corner.

3. Position the battery compartment cover and slide it towards the unit

until it clicks into place.

For optimal performance, we recommend that you charge the handset for

16 hours. You can keep the battery charged by returning the handset to the

telephone base after each use. When the battery power is fully depleted,

a full recharge takes about 16 hours.

IC:xxxxX-xxxxxxxx

FCC ID: XXxxx-xxxx-xx

IC:xxxxX-xxxxxxxx

FCC ID: XXxxx-xxxx-xx

IC:xxxxX-xxxxxxxx

FCC ID: XXxxx-xxxx-xx

IC:xxxxX-xxxxxxxx

FCC ID: XXxxx-xxxx-xx

Make, receive and end calls

Make a call

• Press /FLASH or

to ensure there is a dial tone, then dial the

telephone number.

-OR-

1. Dial the number (press MUTE/REMOVE to make corrections;

press and hold REDIAL/PAUSE to insert a dialing pause).

2. Press /FLASH or to use the speakerphone.

Receive a call

• Press /FLASH,

or any dialing keys (0-9,

or #) to answer an

incoming call.

End a call

• Press OFF/CLEAR or put the handset back in the telephone base

or charger.

Voicemail setup

This feature allows you to use the VOICEMAIL, PLAY, SKIP and ERASE

buttons to access your voicemail (a subscription service available from

your local telephone company for a fee). Before completing these steps, be

sure to have your access number and password to access your voicemail

available. You will also need the key sequence to play, skip and delete your

messages. Contact your local telephone company for more information

about voicemail service.

To program the ACCESS NUMBER button:

1. Press MENU/SELECT from the idle mode.

2. Press or to select VOICEMAIL SETUP, then press

MENU/SELECT.

3. Press or to select ACCESS NUMBER, then press

MENU/SELECT.

4. Use the dial pad to enter the access number. Press MUTE/REMOVE

to delete characters if necessary.

5. Press MENU/SELECT. You’ll hear a conrmation tone.

To program the PASSWORD, PLAY, SKIP and ERASE buttons, follow

the above steps.

To program a pause:

1. Press MENU/SELECT from the idle mode.

2. Press or to select VOICEMAIL SETUP then press MENU/SELECT

twice.

3. The blinking cursor should be at the end of your access number. Press

and hold the REDIAL/PAUSE button until a P appears.

4. Press MENU/SELECT. You’ll hear a conrmation tone.

To reset all codes:

1. Press MENU/SELECT from the idle mode.

2. Press or to select VOICEMAIL SETUP then press MENU/SELECT.

3. Press or to select RESET ALL CODES, then press

MENU/SELECT.

4. The screen displays RESET CODES?

5. Press MENU/SELECT. You’ll hear a conrmation tone.

NOTE:

You must program your voicemail buttons before you can access all of

the functions available with your voicemail.

QSG DS3111-2 071207.indd 1 7/28/2007 5:54:04 PM

IMPORTANT! 1
#) to answer an 1

Résumé du contenu

Page 1 - #) to answer an

Quick start guide for model DS3111-2 NOTES: 1. Use only the power adapters and batteries supplied with your VTech telephone.2. For complete featu

Plus de documents pour Téléphones VTech DS3111-3

Voir le document VTech DS3111-3 Manuel d'utilisateur

VTech DS3111-3 Manuel d'utilisateur (1 pages)

Commentaires sur ces manuels

Pas de commentaire

VTech DS3111-3 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Téléphones VTech DS3111-3. VTech DS3111-3 User`s manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Téléphones VTech DS3111-3

Commentaires sur ces manuels

Produits connexes et manuels pour Téléphones VTech DS3111-3